How Audacity Noise Reduction Works

From Audacity Wiki
Revision as of 09:41, 15 December 2014 by PeterSampson (talk | contribs) (copying the entire contents of the current How Noise Removal Works as the initial draft)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Peter 09Dec14: ToDo-1 It's looking like the new Noise Reduction effect will be replacing Noise Removal in 2.1.0, in which case this page will need to be updated - it will also need a rename (probably with a redirect left behind to catch links to this page - or we could just use a DISPLAYTITLE for the new nomenclature).

Noise Removal

About the algorithm

Q: How do you actually remove noise? What is the algorithm?

A: The noise removal algorithm uses Fourier analysis : it finds the spectrum of pure tones that make up the background noise in the quiet sound segment that you selected - that's called the "frequency spectrum" of the sound. That forms a fingerprint of the static background noise in your sound file. When you remove noise from the music as a whole, the algorithm finds the frequency spectrum of each short segment of sound in your music. Any pure tones that aren't sufficiently louder than the fingerprint (above the threshold to be preserved) are greatly reduced in volume. That way, (say) a guitar note or an overtone of the singer's voice are preserved, but hiss, hum, and other steady noises can be minimized. The general technique is called spectral noise gating .

The first pass of noise removal is done over just noise. For each windowed sample of the sound, we take a Fast Fourier Transform (FFT) and then statistics are tabulated for each frequency band - specifically the maximum level achieved by at least <n> sampling windows in a row, for various values of <n>.

During the noise removal phase, we start by setting a gain control for each frequency band such that if the sound has exceeded the previously-determined threshold, the gain is set to 0, otherwise the gain is set lower (e.g. -18 dB), to suppress the noise. Then frequency-smoothing is applied so that a single frequency is never suppressed or boosted in isolation, followed by time-smoothing so that the gain for each frequency band moves slowly. Lookahead is employed; this effect is not designed for real-time but if it were, there would be a significant delay. The gain controls are applied to the complex FFT of the signal, and then the inverse FFT is applied, followed by a Hanning window; the output signal is then pieced together using overlap/add of half the window size.

Q: How many frequency bands does the noise gate use?

A: In Audacity we use an FFT size of 2048, which results in 1024 frequency bands.


Q: What causes the 'tinkling' artifacts, and what steps can and have been taken to remove them?

A: The tinkly artifacts happen when individual pure tones are near the threshold to be preserved -- they are small pieces of the background soundscape that survived the thresholding, perhaps because the background noise is slightly different from the fingerprint or because the main sound has overtones that are imperceptible but that boost them slightly over the threshold.

So while the Audacity noise gating algorithm could perhaps be improved, any Fourier-based noise removal algorithm will have some artifacts like the "tinkle-bells". They are a symptom of the problem of discrimination - deciding whether a particular analog signal is above or below a decision threshold - that is central to the fields of digital data processing and information theory. In general the tinkle-bell artifacts are quieter than the original noise. The real question is whether they are more noticeable than the original noise. (For example, noise-gating the Beatles' Sun King track off the Abbey Road album is a bad idea, because the soft brushed cymbal sounds merge smoothly into the tape hiss on the original master recording, so tinkle bells and a related problem -- fluttering -- are prominent in noise-gated versions of that track.)

You can reduce the effect of tinkle bells by noise gating sounds that are well separated (either in volume or frequency spectrum) from the background noise, or by mixing a small amount of the original noisy track back into the noise gated sound. Then the muted background noise tends to mask the tinkle bells. That technique works well for (e.g.) noisy microcassette recordings, where the noise floor might only be 20 dB below the loudest sounds on the tape. You can get about 10dB of noise reduction that way, without excessive tinkly artifacts.