Vocal Removal Plug-ins
|This page describes techniques which on some stereo tracks may allow you to remove or isolate vocals (or other parts of a recording) from the rest.
There is no universal, reliable way of doing this unless you have the original multi-track recordings. You need to use whatever technique gives you the most attenuation or isolation on your particular track. This depends on where the vocals are positioned in the stereo field, and on the vocals' precise content compared to the rest of the audio.
Case 1: Vocals in the middle, instruments spread round them
If the vocals are panned in the centre of a stereo track (fairly common in "pop" music tracks), the so-called "vocal removal" technique can sometimes be effective. This removes what is common to both tracks (i.e. the vocals), leaving behind what is different (i.e. the instrumentals).
To try this technique in Audacity, you split the stereo track into its left and right channels, make both mono, invert all (or a selected part) of one of them, and play back the result. See of the for step by step instructions on this technique, or a covering the same process.
You should note that this will remove everything panned in the centre, not just vocals. In pop music this can mean removing the bass and rhythm parts. Removal of the vocals is normally incomplete and will leave artefacts behind, especially where reverberation (echo) is used, and where there are backing vocals. Sometimes certain minor strands of the instrumentals are exposed which are completely covered in the uninverted mix. This technique work particularly badly with tracks where a lot of stereo reverberation has been applied, as this spreads each sound source, and makes them very hard to extract from each other.
Case 2: Vocals in one channel, everything else in the other
If you have an unusual stereo track where the vocals are mixed hard into one channel and everything else hard into the other channel, you can simply split the stereo track into left and right and delete the vocal channel. If you want to isolate the vocals rather than remove them, you can of course delete the other channel. To split a stereo track in Audacity, click on the downward pointing arrow at the top of the Track Panel (where the mute/solo buttons are ) >. Then to delete one of the channels, click the to left of the downward pointing arrow. If you delete the wrong channel, use to get it back. Finally, click the downward pointing arrow again and choose "Mono", so that the track will play out of both speakers.
As well as the above methods which are supported in Audacity itself, there are various third-party plugins that can be used to try and remove or isolate vocals.
Center Pan Remover
There is a Nyquist plugin called "Center Pan Remover" which can automate the steps involved in the Case 1 above so you just have to select the area of track you want to apply the effect to and click . This plugin also has an option to merely invert a range of frequencies in one channel rather than invert the whole channel (and so may be less destructive of the non-vocal parts of the music than a simple inversion of one channel). Note that although two channels of output are produced, the result is mono because both channels will be identical.. This can be downloaded from the
To install this plugin, place it in the Plug-Ins folder inside the Audacity installation folder. On Windows computers, this is usually under "Program Files" The plugin will be available after restarting Audacity, underneath the divider in the Effect Menu.
Two Windows VST plugins are known of that can be used in Audacity for vocal removal and isolation.
- can sometimes remove vocals where they are not centre-panned but are rather different in frequency make-up compared to the non-vocal parts of the track. This is a free plugin. It works on two mono tracks (split from a stereo track and made mono as above) by extracting the right channel frequencies from the left hand frequencies, leaving the "result" in the former left channel. Alternatively, if your vocals are centre-panned, this plugin can often make a good job of isolating them (as opposed to removing them).
- is a commercial plugin and features centre channel removal by frequency-based and cepstral methods (i.e. not a simple subtraction of one channel from the other) and has an advantage over kn0ck0ut of providing stereo output for the "vocals removed" track. It also offers the option of isolating centre-panned content. There is a demo version with a "mild" vocal removal setting (but no isolation ability) that works in Audacity.
If you wanted to try either of these VST plugins in Audacity, simply place the unzipped .dll file from the plugin's zip folder, along with the unzipped vst-bridge.dll from the Audacity into Audacity's Plug-Ins folder. The Plug-Ins folder will be in the folder into which you installed Audacity, usually C:\Program_Files\Audacity. On restarting Audacity, the new plugin will appear in the Effect Menu underneath the divider. Should vst-bridge.dll not work, try the . Simply place the already unzipped VST Enabler.dll in Audacity's Plug-Ins folder along with the plugin's own .dll, then exit and restart Audacity.
Note that all VST plugins in Audacity only have a generic tabular interface due to licensing restrictions imposed by Steinberg.
There is also an additional commercial VST plugin called ExtraBoy which offers useful functionality for those interested in vocal removal or modification of the different components of an audio track. There are two versions of this plugin, but unfortunately neither work properly with the currently limited VST support that Audacity can offer. It seems that the processed audio is always completely silenced irresepective of the plugin settings used. Both versions of ExtraBoy do function with other audio editors which offer full VST support, so you could always export a track from your Audacity Project as a WAV or AIFF file and process it in Extraboy in another editor.
The is quite similar to VoiceTrap but offers some vocal removal ability on all tracks (not just on centre-panned vocals). It has two "vocal removal" algorithms (1) on the basis of the vocals' frequency characteristics, and (2) on the basis of their spread in the stereo spectrum. The two algorithms can be combined to obtain the best possible removal in a particular case, and full stereo information is preserved in the processed track. A "vocal isolation" algorithm is also provided.
The claims to be capable of isolating, removing, suppressing or enhancing any component of a stereo track, based on its identified frequency and spatial "signature". Naturally the author points out that the exact results are subject to the particular characteristics of each track. Multiple components of a track can be processed simultaneously (e.g. isolate piano and vocal, or enhance piano and bass).
OS X Plugins
On OS X you can try the Audio Units plugin (14 day free evaluation) in Audacity, as long as you use Audacity 1.3.2 or later, for which you must be on OS X 10.3 or higher.
This is rather similar to the Nyquist Center Pan Remover in that it aims to reduce the strength of centre panned vocals but is slightly different in that it has a phase offset adjustment and a slider for adjusting the intensity of the vocal reduction.
Try putting the voxreducer.component in either of these two locations as Audacity should see it there:
If that does not work you could try either of these locations (as suggested by the program documentation):